Instructions and Maintenance of Inflatable Toys

充气玩具的安装：

Installation of inflatable toys:

1.将设备放置在平整地面上，设备下面最好放一垫布（如地毡，塑料彩条布），然后 将其展开。

1. Place the equipment on the flat ground. It is better to put a mat (such as carpet, plastic strip cloth) under the equipment, and then unfold it.

2.找到设备的进风口，再与风机出风口相连接，并把风机口扎紧，再将备用的进风口用绳子扎紧。

2. Find the air inlet of the equipment, then connect it with the air outlet of the fan, and fasten the air outlet tightly, then tie the spare air inlet tightly with rope.

3.把鼓风机接通电源，设备在5-10分钟内就会鼓起。

3. Turn the blower on and the equipment will bulge up in 5-10 minutes.

配套风机的安装:

Installation of matching fans:

1.选用国标1.5mm2-4mm电缆线若干米与风机相连接 ，另一端连接空气开关，并接上 触电保护器。

1. Select the national standard 1.5 mm 2-4 mm cable several meters to connect with the fan, the other end to connect with the air switch, and connect with the shock protector.

2.使用前应先检查电源电压是否和铭牌相符，旋转方向是否正确。

2. Before using, check whether the voltage of the power supply matches the nameplate and the direction of rotation is correct.

3.应将机壳接一可靠的地线，并定期检查，把风机的进风口按上防护网，以免发生意外事故。

3. The casing should be connected to a reliable ground wire and checked regularly. The air inlet of the fan should be put on the protective net so as to avoid accidents.

设备的保洁收藏：

Cleaning Collection of Equipment:

1.切断电源，打开风机接口及排气口，排气时间一般在10-25分钟，余气要挤压。如果设备因为雨天进水，务必把水排净并晾干。

1. Cut off the power supply, open the fan interface and exhaust port, the exhaust time is generally 10-25 minutes,wanji.89ix.com fengguan.89ix.comfengguanol.89ix.comtianchuangp.89ix.com jietou.89ix.com fenxiyi.89ix.com the remaining air to be squeezed. If the equipment enters the water on rainy days, make sure that the water is drained and dried.

2.做清洁处理，可使用洗衣粉将其污渍、油渍擦去，然后用清水擦洗干净，晒晾干即可。

2. Do cleaning treatment, can use laundry detergent to wipe off its stains, oil stains, and then clean with clean water, dry.

3.将设备折叠，用底面折拦住正面，再用篷布将其盖好。

3. Fold the equipment, fold the front with the bottom and cover it with tarpaulin.

4.如果长期不用，把干净的设备折叠，打捆，包装好。仓储温度一般在-50～+40摄氏度为宜。

4. If it is not used for a long time, fold, bundle and pack clean equipment. Storage temperature is generally - 50 to + 40 degrees Celsius.

5.风机应注意防潮、防腐蚀。气模设备要注意防鼠虫蛀咬。

5. Fans should be moistureproof and anti-corrosion. Attention should be paid to the prevention of rodent and insect bites in the air model equipment.

维护办法：

Maintenance measures:

1.为了保证您的设备达到正常的使用年限，在开机游玩时不能参加过多的孩子游玩。一般在气模上容纳3平方米一个孩子。

1. In order to ensure the normal life of your equipment, you should not take part in too many children's games when playing on the computer. Generally, it can accommodate a child of 3 square meters on the air mold.

2.设施上的小造型起装饰作用，不能让孩子硬拉、硬撕以免损坏。

2. The small shape on the facility plays a decorative role. Children should not be forced to pull or tear hard to avoid damage.

3.孩子游玩时，不能让孩子用坚硬物在设备上乱写乱画，以免损坏。

3. When children play, they should not use hard objects to scribble on the equipment in order to avoid damage.

4.如遇设备破损，可在破损处和备用的PVC材料上都涂上专用胶，待胶5分钟后不粘手，将其粘合，适当挤压，数分钟便可以使用。

4. If the equipment is damaged, special glue can be applied to the damaged place and the spare PVC material. After 5 minutes, the glue will not stick to the hand, then it will be bonded and extruded properly, then it can be used in a few minutes.

5.设备上的气压太软，检查有没有过多漏气，撕洞，或者停电；气压太硬，要把风机 的进风口遮挡一点。

5. The air pressure on the equipment is too soft. Check if there is too much air leakage, tearing holes, or power failure. If the air pressure is too hard, cover the air inlet of the fan a little.

6.如大面积非正常使用损坏，厂方可以提供专业维修服务，或者直接寄回厂里进行维修。

6. If a large area of abnormal use is damaged, the manufacturer can provide professional maintenance services, or send it directly back to the factory for maintenance.